实操 :华为DHCP中继服务配置(实操课程)

网友投稿 389 2022-09-12


实操 :华为DHCP中继服务配置(实操课程)

前言:

该实验是华为模拟器eNSP模拟器、dhcp中继实验#DHCP中继的应用场景:通常在DHCP分配网段过多的情况下,网关路由器上配置DHCP服务,压力过大,一般我们用第二路由器,或则第二台DHCP服务器来分担业务

dhcp 中继

system-view Enter system view, return user view with Ctrl+Z. [Huawei]sysname LSW1 [LSW1]un in en Info: Information center is disabled. [LSW1]vlan bat 10 20 Info: This operation may take a few seconds. Please wait for a moment...done. [LSW1]int e 0/0/1 [LSW1-Ethernet0/0/1]p l a [LSW1-Ethernet0/0/1]p d v 10 [LSW1-Ethernet0/0/1]un sh Info: Interface Ethernet0/0/1 is not shutdown. [LSW1-Ethernet0/0/1]int e 0/0/2 [LSW1-Ethernet0/0/2]p l a [LSW1-Ethernet0/0/2]p d v 20 [LSW1-Ethernet0/0/2]un sh Info: Interface Ethernet0/0/2 is not shutdown. [LSW1-Ethernet0/0/2]int e 0/0/3 [LSW1-Ethernet0/0/3]p l a [LSW1-Ethernet0/0/3]p d v 10 [LSW1-Ethernet0/0/3]un sh Info: Interface Ethernet0/0/3 is not shutdown. [LSW1-Ethernet0/0/3]int e 0/0/4 [LSW1-Ethernet0/0/4]p l a [LSW1-Ethernet0/0/4]p d v 20 [LSW1-Ethernet0/0/4]un sh Info: Interface Ethernet0/0/4 is not shutdown. [LSW1-Ethernet0/0/4]int g 0/0/1 [LSW1-GigabitEthernet0/0/1]p l t [LSW1-GigabitEthernet0/0/1]p t a v a [LSW1-GigabitEthernet0/0/1]un sh Info: Interface GigabitEthernet0/0/1 is not shutdown. [LSW1-GigabitEthernet0/0/1]dis vlan The total number of vlans is : 3 1 common UT:Eth0/0/5(D) Eth0/0/6(D) Eth0/0/7(D) Eth0/0/8(D) Eth0/0/9(D) Eth0/0/10(D) Eth0/0/11(D) Eth0/0/12(D) Eth0/0/13(D) Eth0/0/14(D) Eth0/0/15(D) Eth0/0/16(D) Eth0/0/17(D) Eth0/0/18(D) Eth0/0/19(D) Eth0/0/20(D) Eth0/0/21(D) Eth0/0/22(D) GE0/0/1(U) GE0/0/2(D) 10 common UT:Eth0/0/1(U) Eth0/0/3(U) TG:GE0/0/1(U) 20 common UT:Eth0/0/2(U) Eth0/0/4(U) TG:GE0/0/1(U) [LSW1-GigabitEthernet0/0/1] [LSW1-GigabitEthernet0/0/1]dis int b InUti/OutUti: input utility/output utility Interface PHY Protocol InUti OutUti inErrors outErrors Ethernet0/0/1 up up 0% 0% 0 0 Ethernet0/0/2 up up 0% 0% 0 0 Ethernet0/0/3 up up 0% 0% 0 0 Ethernet0/0/4 up up 0% 0% 0 0 GigabitEthernet0/0/1 up up 0% 0% 0 0

R1

system-view Enter system view, return user view with Ctrl+Z. [Huawei]un in en Info: Information center is disabled. [Huawei]dhcp enable Info: The operation may take a few seconds. Please wait for a moment.done. [Huawei]int g 0/0/0 [Huawei-GigabitEthernet0/0/0]ip add 14.0.0.1 24 [Huawei-GigabitEthernet0/0/0]un sh Info: Interface GigabitEthernet0/0/0 is not shutdown. [Huawei-GigabitEthernet0/0/0]int g 0/0/3 [Huawei-GigabitEthernet0/0/3]ip add 12.0.0.1 24 [Huawei-GigabitEthernet0/0/3]un sh Info: Interface GigabitEthernet0/0/3 is not shutdown. [Huawei-GigabitEthernet0/0/3]q [Huawei]vlan bat 10 20 Info: This operation may take a few seconds. Please wait for a moment...done. [Huawei]int g 0/0/1.10 [Huawei-GigabitEthernet0/0/1.10]dot1q termination vid 10 [Huawei-GigabitEthernet0/0/1.10]ip add 192.168.10.1 24 [Huawei-GigabitEthernet0/0/1.10]un sh Info: Interface GigabitEthernet0/0/1.10 is not shutdown. [Huawei-GigabitEthernet0/0/1.10]q [Huawei]int g 0/0/1.10 [Huawei-GigabitEthernet0/0/1.10]dis this # interface GigabitEthernet0/0/1.10 dot1q termination vid 10 ip address 192.168.10.1 255.255.255.0 # return [Huawei-GigabitEthernet0/0/1.10]a b e [Huawei-GigabitEthernet0/0/1.10]dhcp select relay [Huawei-GigabitEthernet0/0/1.10]dhcp relay server-ip 14.0.0.2 [Huawei-GigabitEthernet0/0/1.10]q [Huawei]int g 0/0/1.20 [Huawei-GigabitEthernet0/0/1.20]dot1q termination vid 20 [Huawei-GigabitEthernet0/0/1.20]ip add 192.168.20.1 24 [Huawei-GigabitEthernet0/0/1.20]a b e [Huawei-GigabitEthernet0/0/1.20]dhcp select relay [Huawei-GigabitEthernet0/0/1.20]dhcp relay server-ip 14.0.0.2 [Huawei-GigabitEthernet0/0/1.20]q [Huawei]ip route-static 15.0.0.0 24 12.0.0.2 [Huawei]

R2

system-view Enter system view, return user view with Ctrl+Z. [Huawei]sysname R2 [R2]un in en Info: Information center is disabled. [R2]int g 0/0/3 [R2-GigabitEthernet0/0/3]ip add 12.0.0.2 24 [R2-GigabitEthernet0/0/3]un sh Info: Interface GigabitEthernet0/0/3 is not shutdown. [R2-GigabitEthernet0/0/3]int e 0/0/0 [R2-Ethernet0/0/0]q [R2]dhcp enable Info: The operation may take a few seconds. Please wait for a moment.done. [R2]int e 0/0/0 [R2-Ethernet0/0/0]ip add 15.0.0.1 24 [R2-Ethernet0/0/0]un sh Info: Interface Ethernet0/0/0 is not shutdown. [R2-Ethernet0/0/0]dhcp select relay [R2-Ethernet0/0/0]dhcp relay server-ip 14.0.0.2 [R2-Ethernet0/0/0]q [R2]ip route-static 14.0.0.0 24 12.0.0.1 [R2]ip route-static 192.168.0.0 16 12.0.0.1 [R2]dis ip ? as-path-filter Specify regular expression access list number community-filter Add a community-filter entry error Information of error packet extcommunity-filter Match BGP/VPN extended community filter ha Display information of socket HA host Host table(s) interface Show information of interfaces ip-prefix Specify an address prefix-list ipv6-prefix Specify an IPv6 address prefix-list netstream Netstream feature policy-based-route Display policy based routing information pool Configure a local IP pool prefix-limit Prefix limit rd-filter Route-distinguisher filter routing-table Routing table socket Display information of created sockets statistics Display statistics information of datagram topology The name of topology userlog Userlog feature vpn-instance VPN instance information [R2]dis ip routing-table Route Flags: R - relay, D - download to fib ------------------------------------------------------------------------------ Routing Tables: Public Destinations : 8 Routes : 8 Destination/Mask Proto Pre Cost Flags NextHop Interface 12.0.0.0/24 Direct 0 0 D 12.0.0.2 GigabitEthernet 0/0/3 12.0.0.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/3 14.0.0.0/24 Static 60 0 RD 12.0.0.1 GigabitEthernet 0/0/3 15.0.0.0/24 Direct 0 0 D 15.0.0.1 Ethernet0/0/0 15.0.0.1/32 Direct 0 0 D 127.0.0.1 Ethernet0/0/0 127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0 127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0 192.168.0.0/16 Static 60 0 RD 12.0.0.1 GigabitEthernet 0/0/3 [R2]

R3

system-view Enter system view, return user view with Ctrl+Z. [Huawei]sysname R3 [R3]un in en Info: Information center is disabled. [R3]dhcp enable Info: The operation may take a few seconds. Please wait for a moment.done. [R3]int g 0/0/0 [R3-GigabitEthernet0/0/0]ip add 14.0.0.2 24 [R3-GigabitEthernet0/0/0]un sh Info: Interface GigabitEthernet0/0/0 is not shutdown. [R3-GigabitEthernet0/0/0]dhcp select global [R3-GigabitEthernet0/0/0]q [R3]ip pool dhcp192.168.10.0 Info:It's successful to create an IP address pool. [R3-ip-pool-dhcp192.168.10.0]network 192.168.10.0 mask 24 [R3-ip-pool-dhcp192.168.10.0]gateway 192.168.10.1 [R3-ip-pool-dhcp192.168.10.0]dns-list 1.1.1.1 [R3-ip-pool-dhcp192.168.10.0]? ip-pool view commands: arp-ping ARP-ping ce-ping Ce-ping tool configuration Configuration interlock display Display current system information dns-list Configure DNS servers domain-name Configure domain name excluded-ip-address Mark disable IP addresses gateway-list Configure the gateway import Imports the following network configuration parameters from a central server into local ip pool database: domain name, dns server and netbios server. lease Configure the lease of the IP pool lock Lock the IP pool mac-populate Populate an OAM MAC to FDB entry mac-purge Purge an OAM MAC from FDB entry monitor System monitor dynamic show mtrace Trace route to multicast source nbns-list Configure the windows's netbios name servers netbios-type Netbios node type network Add a network next-server The address of the server to use in the next step of the client's bootstrap process. option Configure the DHCP options option121 DHCP option 121 option184 DHCP option 184 ping Send echo messages quit Exit from current command view reset Reset operation return Exit to user view screen-width Set screen width static-bind Static bind test-aaa Accounts test trace Trace route (switch) to host on Data Link Layer tracert Trace route to host undo Cancel current setting vpn-instance Config VPN instance vrbd Display version information [R3-ip-pool-dhcp192.168.10.0]q [R3]ip pool dhcp192.168.20.0 Info:It's successful to create an IP address pool. [R3-ip-pool-dhcp192.168.20.0]network 192.168.20.0 mask 24 [R3-ip-pool-dhcp192.168.20.0]gateway-list 192.168.20.1 [R3-ip-pool-dhcp192.168.20.0]dns-list 1.1.1.1 2.2.2.2 [R3-ip-pool-dhcp192.168.20.0]q [R3]ip pool dhcp15.0.0.0 Info:It's successful to create an IP address pool. [R3-ip-pool-dhcp15.0.0.0]network 15.0.0.0 mask 24 [R3-ip-pool-dhcp15.0.0.0]static-bind ip-address 15.0.0.88 mac-address 5489-98A B-2A25 Error:Please configure the gateway first. [R3-ip-pool-dhcp15.0.0.0]gateway-list 15.0.0.1 [R3-ip-pool-dhcp15.0.0.0]static-bind ip-address 15.0.0.88 mac-address 5489-98AB- 2A25 [R3-ip-pool-dhcp15.0.0.0]q [R3]ip route-static 0.0.0.0 0.0.0.0 14.0.0.1 [R3]


版权声明:本文内容由网络用户投稿,版权归原作者所有,本站不拥有其著作权,亦不承担相应法律责任。如果您发现本站中有涉嫌抄袭或描述失实的内容,请联系我们jiasou666@gmail.com 处理,核实后本网站将在24小时内删除侵权内容。

上一篇:Tungsten Fabric中文社区介绍
下一篇:全网最全最细的jmeter接口测试教程以及接口测试流程(入门教程)
相关文章

 发表评论

暂时没有评论,来抢沙发吧~