华为无线设备WLAN QoS配置命令（华为无线设备维护基础培训）

华为无线设备WLAN QoS配置命令（华为无线设备维护基础培训）

[huawei]wlan

[huawei-wlan-view]radio-2g-profile name r2

[huawei-wlan-radio-2g-prof-r2]undo wmm disable  //使能WMM功能,缺省使能

[huawei-wlan-radio-2g-prof-r2]wmm mandatory enable  //禁止不支持WMM功能的STA连接到已使能WMM功能的AP上

[huawei-wlan-radio-2g-prof-r2]wmm edca-ap ac-be aifsn 1 //配置AP上的EDCA参数

[huawei-wlan-radio-2g-prof-r2]wmm edca-ap ac-vo ecw ecwmin 1 ecwmax 1

[huawei-wlan-radio-2g-prof-r2]wmm edca-ap ac-vi txoplimit 1

[huawei-wlan-radio-2g-prof-r2]wmm edca-ap ac-bk ack-policy normal  //配置AP上的ACK策略

[huawei-wlan-view]ssid-profile name s1

[huawei-wlan-ssid-prof-s1]wmm edca-client ac-be aifsn 1  //配置STA上的EDCA参数

[huawei-wlan-view]traffic-profile name t1  //创建流量模板并进入流量模板视图,缺省系统存在名为“default”的流量模板

[huawei-wlan-traffic-prof-t1]priority-map downstream trust dot1p  //配置网络上数据下行至AP时，802.3报文到802.11报文的映射方式,缺省为DSCP

[huawei-wlan-traffic-prof-t1]priority-map downstream trust dscp

[huawei-wlan-traffic-prof-t1]priority-map downstream dscp 1 to 2 dot11e 1  //配置网络上数据下行至AP时，802.3报文的DSCP优先级到802.11报文的UP优先级的映射关系

[huawei-wlan-traffic-prof-t1]priority-map downstream dot1p 1 to 2 dot11e 1  //配置网络上数据下行至AP时，802.3报文的802.1p优先级到802.11报文的UP优先级的映射关系

[huawei-wlan-traffic-prof-t1]priority-map tunnel-upstream trust dot11e  //配置AP上数据上行至AC时，802.11报文到隧道报文的映射方式,缺省为802.11e

[huawei-wlan-traffic-prof-t1]priority-map tunnel-upstream trust dscp

[huawei-wlan-traffic-prof-t1]priority-map tunnel-upstream dot11e 1 to 2 dscp 1  //配置AP上数据上行至AC时，802.11报文的UP优先级到隧道报文的DSCP优先级的映射关系

[huawei-wlan-traffic-prof-t1]priority-map  tunnel-upstream dot11e 1 to 2 dot1p 1  //配置AP上数据上行至AC时，802.11报文的UP优先级到隧道报文的802.1p优先级的映射关系

[huawei-wlan-traffic-prof-t1]priority-map tunnel-upstream dscp 1 to 2 tunnel-dscp 1  //配置AP上数据上行至AC时，802.11报文的DSCP优先级到隧道报文的DSCP优先级的映射关系

[huawei-wlan-traffic-prof-t1]priority-map tunnel-upstream dscp 1 to 2 dot1p 1  //配置AP上数据上行至AC时，802.11报文的DSCP优先级到隧道报文的802.1p优先级的映射关系

[huawei-wlan-view]vap-profile name v1

[huawei-wlan-vap-prof-v1]traffic-profile t1  //在VAP模板中引用流量模板

[huawei]display traffic-profile all  //查看流量模板中关于优先级映射的配置信息

[huawei-wlan-view]traffic-profile name t1  //创建流量模板并进入流量模板视图

[huawei-wlan-traffic-prof-t1]rate-limit client up 64  //配置VAP内所有STA或每个STA上下行报文的限制速率, 缺省为4294967295Kbps

[huawei-wlan-traffic-prof-t1]rate-limit client down 64

[huawei-wlan-traffic-prof-t1]rate-limit vap up 64

[huawei-wlan-traffic-prof-t1]rate-limit vap down 64

[huawei-wlan-view]ssid-profile name s1  //进入SSID模板视图

[huawei-wlan-ssid-prof-s1]qos car inbound cir 64  //配置QoS CAR参数

[huawei-wlan-view]rrm-profile name r1  //创建RRM模板并进入RRM模板视图

[huawei-wlan-rrm-prof-r1]airtime-fair-schedule enable  //使能AP射频的Airtime调度功能

[huawei-wlan-view]radio-2g-profile name r1

[huawei-wlan-radio-2g-prof-r1]rrm-profile r1  //将RRM模板绑定到2G射频模板

[huawei-wlan-view]traffic-profile name t1  //创建流量模板并进入流量模板视图

[huawei-wlan-traffic-prof-t1]traffic-filter inbound ipv4 acl 3000  //在流量模板下配置基于ACL的报文过滤

[huawei-wlan-traffic-prof-t1]traffic-filter outbound ipv4 acl 3000

[huawei-wlan-traffic-prof-t1]traffic-remark inbound ipv4 acl 3000 dot11e 1  //在流量模板下配置基于ACL的报文重标记

[huawei-wlan-traffic-prof-t1]traffic-remark inbound ipv4 acl 3000 dscp 1

[huawei-wlan-traffic-prof-t1]traffic-remark outbound ipv4 acl 3000 dscp 1

[huawei-wlan-traffic-prof-t1]traffic-remark outbound ipv4 acl 3000 dot11e 1

[huawei-wlan-traffic-prof-t1]user-isolate l2  //使能流量模板下用户隔离功能

[huawei]lync listener 1025  //使能交换机与Lync服务器交互的功能，并指定服务端口号

版权声明：本文内容由网络用户投稿，版权归原作者所有，本站不拥有其著作权，亦不承担相应法律责任。如果您发现本站中有涉嫌抄袭或描述失实的内容，请联系我们jiasou666@gmail.com 处理，核实后本网站将在24小时内删除侵权内容。