CCNP(BSCI)实验：基础IPv6实验

CCNP(BSCI)实验：基础IPv6实验

第一步：配置各路由器的接口IPv6地址R1(config)#int s2/1R1(config-if)#ipv6 add 2001:1::/64 eui-64 R1(config-if)#no shR1(config-if)#int lo0R1(config-if)#ipv6 add 1::1/64

R2(config)#int s2/1R2(config-if)#ipv6 add 2001:1::1/64 eui-64 R2(config-if)#no shR2(config-if)#int lo0R2(config-if)#ipv6 add 2::1/64第二步：配置IPv6的静态路由R1(config)#ipv route 2::1/64 s2/1R2(config)#ipv route 1::1/64 s2/1第三步：查看IPv6路由R1# sh ipv rouIPv6 Routing Table - 7 entriesCodes: C - Connected, L - Local, S - Static, R - RIP, B - BGPU - Per-user Static routeI1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summaryO - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2C 1::/64 [0/0]via ::, Loopback0L 1::1/128 [0/0]via ::, Loopback0S 2::/64 [1/0]via ::, Serial2/1C 2001:1::/64 [0/0]via ::, Serial2/1L 2001:1::C891:BFF:FE4C:0/128 [0/0]via ::, Serial2/1L FE80::/10 [0/0]via ::, Null0L FF00::/8 [0/0]via ::, Null0

R2#sh ipv rouIPv6 Routing Table - 7 entriesCodes: C - Connected, L - Local, S - Static, R - RIP, B - BGPU - Per-user Static routeI1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summaryO - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2S 1::/64 [1/0]via ::, Serial2/1C 2::/64 [0/0]via ::, Loopback0L 2::1/128 [0/0]via ::, Loopback0C 2001:1::/64 [0/0]via ::, Serial2/1L 2001:1::C892:EFF:FE64:0/128 [0/0]via ::, Serial2/1L FE80::/10 [0/0]via ::, Null0L FF00::/8 [0/0]via ::, Null0

第四步：调试过程R2#debug ipv packet IPv6 unicast packet debugging is onR2#ping 1::1

Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 1::1, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 12/29/44 ms

版权声明：本文内容由网络用户投稿，版权归原作者所有，本站不拥有其著作权，亦不承担相应法律责任。如果您发现本站中有涉嫌抄袭或描述失实的内容，请联系我们jiasou666@gmail.com 处理，核实后本网站将在24小时内删除侵权内容。