链路聚合综合实验（链路聚合实验总结）

链路聚合综合实验（链路聚合实验总结）

链路聚合综合实验

1 问题如何在复杂的网络环境中配置链路聚合模式？步骤实现此案例需要按照如下步骤进行。

1）路由器配置 r1、r2

每个路由器上各建两个eth-trunk端口，分别连接路由器和三层交换机2）配置三层交换机 sw3、sw6

每个三层交换机上各建三个eth-trunk端口，分别连接路由器和二层交换机，vlan 10 20 1003）配置二层交换机 sw3、sw4、sw5、sw6

每个二层交换机创建一个eth-trunk端口，连接到三层交换机，vlan 104）配置PC机的IP地址

5）测试网络连接

[r2]int Eth-Trunk 1 /设置聚合链路1[r2-Eth-Trunk1]undo portswitch -undo portswitch是把二层接口切换成三层接口，然后就可以在接口下面配置IP地址了！ [r2-Eth-Trunk1]mode lacp-static /配置lacp自动模式[r2-Eth-Trunk1]trunkport g0/0/0 /加入接口Info: This operation may take a few seconds. Please wait for a moment...done.[r2-Eth-Trunk1]trunkport g0/0/1Info: This operation may take a few seconds. Please wait for a moment...done.[r2-Eth-Trunk1]q [r2]int Eth-Trunk 2[r2-Eth-Trunk2]undo portswitch [r2-Eth-Trunk2]mode l [r2-Eth-Trunk2]mode lacp-static [r2-Eth-Trunk2]trunkport g2/0/1Info: This operation may take a few seconds. Please wait for a moment...done.[r2-Eth-Trunk2]trunkport g2/0/2Info: This operation may take a few seconds. Please wait for a moment...done. [r2-Eth-Trunk2]ip addres 192.168.3.1 24 [r2]int Eth-Trunk 1[r2-Eth-Trunk1]ip add 192.168.2.2 24 dis ip routing-table Enter system view, return user view with Ctrl+Z.[r2]ip route-static 192.168.30.0 24 192.168.3.2 设置静态路由[r2]ip route-static 192.168.40.0 24 192.168.3.2[r2]ip route-static 192.168.10.0 24 192.168.2.1[r2]ip route-static 192.168.20.0 24 192.168.2.1[r2]ip route-static 192.168.1.0 24 192.168.2.1[r2]dis ip routing-table

[sw3]vlan batch 10 20 100Info: This operation may take a few seconds. Please wait for a moment...done. [sw3]int Eth-Trunk 1[sw3-Eth-Trunk1]mode lacp-static [sw3-Eth-Trunk1]trunkport g0/0/3Info: This operation may take a few seconds. Please wait for a moment...done.[sw3-Eth-Trunk1]trunkport g0/0/4Info: This operation may take a few seconds. Please wait for a moment...done.[sw3-Eth-Trunk1]port link-type trunk [sw3-Eth-Trunk1]port trunk allow-pas vlan all[sw3-Eth-Trunk1]q [sw3]int Eth-Trunk 2[sw3-Eth-Trunk2]mode lacp-static[sw3-Eth-Trunk2]trunkport g0/0/5Info: This operation may take a few seconds. Please wait for a moment...done.[sw3-Eth-Trunk2]trunkport g0/0/6Info: This operation may take a few seconds. Please wait for a moment...done.[sw3-Eth-Trunk2]port link-type trunk[sw3-Eth-Trunk2]port trunk allow-pas vlan all[sw3-Eth-Trunk2]q [sw3]int Eth-Trunk 3[sw3-Eth-Trunk3]mode lacp-static [sw3-Eth-Trunk3]trunkport g0/0/1Info: This operation may take a few seconds. Please wait for a moment...done.[sw3-Eth-Trunk3]trunkport g0/0/2Info: This operation may take a few seconds. Please wait for a moment...done.[sw3-Eth-Trunk3]port link-type acces [sw3-Eth-Trunk3]port default vlan 100[sw3-Eth-Trunk3]q [sw3]int Vlanif 10[sw3-Vlanif10]ip addres 192.168.10.1 24[sw3-Vlanif10]int Vlanif 20[sw3-Vlanif20]ip addres 192.168.20.1 24[sw3-Vlanif20]int Vlanif 100[sw3-Vlanif100]ip addres 192.168.1.2 24[sw3]dis port vlan[sw3]dis ip int b

[sw3]ip route-static 192.168.2.0 24 192.168.1.1[sw3]ip route-static 192.168.3.0 24 192.168.1.1[sw3]ip route-static 192.168.30.0 24 192.168.1.1[sw3]ip route-static 192.168.40.0 24 192.168.1.1[sw3]q

[sw1]vlan batch 10Info: This operation may take a few seconds. Please wait for a moment...done. [sw1]int Eth-Trunk 1[sw1-Eth-Trunk1]mode lacp-static [sw1-Eth-Trunk1]trunkport e0/0/3Info: This operation may take a few seconds. Please wait for a moment...done.[sw1-Eth-Trunk1]trunkport e0/0/4Info: This operation may take a few seconds. Please wait for a moment...done.[sw1-Eth-Trunk1]port link-type trunk[sw1-Eth-Trunk1]port trunk allow-pas vlan all[sw1-Eth-Trunk1]q[sw1]int e0/0/1[sw1-Ethernet0/0/1]port link-type acces[sw1-Ethernet0/0/1]port default vlan 10

版权声明：本文内容由网络用户投稿，版权归原作者所有，本站不拥有其著作权，亦不承担相应法律责任。如果您发现本站中有涉嫌抄袭或描述失实的内容，请联系我们jiasou666@gmail.com 处理，核实后本网站将在24小时内删除侵权内容。