三层交换配置路由（三层交换机静态路由配置）

三层交换配置路由（三层交换机静态路由配置）

三层交换配置路由

3.1 问题如何使用三层交换机和路由配置实现全网互通？配置思路：1.终端设备pc2.交换机-sw1.2.4 接口设置3.三层交换-sw3建立vlan-与交换机连接设置trunk允许所有-vlanif 设置ip地址-创建vlan 300 接口0/0/3设置acce模式加入vlan 300 进入vlanif 300 设置ip地址-设置静态路由60 70网段下一跳 4.路由器-子接口设置ip地址 打开ARP广播-g0/0/2接口设置IP地址-设置默认静态路由5.验证与测试

SW1SW2

[SW4]vlan batch 10 20 30 40 50 60 70Info: This operation may take a few seconds. Please wait for a moment...done.[SW4]int e0/0/1[SW4-Ethernet0/0/1]port link-type access [SW4-Ethernet0/0/1]port default vlan 60[SW4-Ethernet0/0/1]int e0/0/2 [SW4-Ethernet0/0/2]port link-type access [SW4-Ethernet0/0/2]port default vlan 70[SW4-Ethernet0/0/2]int e0/0/3 [SW4-Ethernet0/0/3]port link-type trunk [SW4-Ethernet0/0/3]port trunk allow-pass vlan all

[SW3]vlan batch 10 20 30 40 50 60 70Info: This operation may take a few seconds. Please wait for a moment...done.[SW3]port-group 1[SW3-port-group-1]group-member g0/0/1 g0/0/2 [SW3-port-group-1]port link-type trunk [SW3-port-group-1]port trunk allow-pass vlan all[SW3]int vlanif 10[SW3-Vlanif10]ip add 192.168.10.1 24[SW3-Vlanif10]int v20[SW3-Vlanif20]ip add 192.168.20.1 24[SW3-Vlanif20]int v30[SW3-Vlanif30]ip add 192.168.30.1 24[SW3-Vlanif30]int v40[SW3-Vlanif40]ip add 192.168.40.1 24[SW3-Vlanif40]int v50 [SW3-Vlanif50]ip add 192.168.50.1 24[SW3-Vlanif50]q[SW3]vlan 300[SW3-vlan300]q[SW3]int g0/0/3 [SW3-GigabitEthernet0/0/3]port link-type access [SW3-GigabitEthernet0/0/3]port default vlan 300[SW3-GigabitEthernet0/0/3]q[SW3]int vlanif 300[SW3-Vlanif300]ip add 192.168.3.3 24[SW3-Vlanif300]q [SW3]ip route-static 192.168.60.0 24 192.168.3.1[SW3]ip route-static 192.168.70.0 24 192.168.3.1

[R1]int g0/0/0.1[R1-GigabitEthernet0/0/0.1]dot1q termination vid 60[R1-GigabitEthernet0/0/0.1]ip add 192.168.60.1 24[R1-GigabitEthernet0/0/0.1]arp broadcast enable [R1-GigabitEthernet0/0/0.1]int g0/0/0.2[R1-GigabitEthernet0/0/0.2]dot1q termination vid 70[R1-GigabitEthernet0/0/0.2]ip add 192.168.70.1 24 [R1-GigabitEthernet0/0/0.2]arp broadcast enable [R1-GigabitEthernet0/0/0.2]q[R1]int g0/0/02[R1-GigabitEthernet0/0/2]ip add 192.168.3.1 24

g0/0/0.1 192.168.60.1 24g0/0/0.2 192.168.70.1 24进入子接口 设置ip地址 开启arp广播

版权声明：本文内容由网络用户投稿，版权归原作者所有，本站不拥有其著作权，亦不承担相应法律责任。如果您发现本站中有涉嫌抄袭或描述失实的内容，请联系我们jiasou666@gmail.com 处理，核实后本网站将在24小时内删除侵权内容。