多平台统一管理软件接口,如何实现多平台统一管理软件接口
317
2022-09-23
静态路由、负载分担、浮动路由(浮动静态路由的配置方法)
第六天 HCIA 149
今日授课内容:
1、静态路由介绍
静态路由的配置第一步:基本配置IP地址 连通性的测试
第二步:R1访问192.168.23.3路由[R1]ip route-static 192.168.23.0 24 GigabitEthernet 0/0/0 192.168.12.2
检查静态路由是否生效[R1]display ip routing-table protocol static Route Flags: R - relay, D - download to fib
Public routing table : StaticDestinations : 1 Routes : 1 Configured Routes : 1
Static routing table status :
Destination/Mask Proto Pre Cost Flags NextHop Interface
192.168.23.0/24 Static 60 0 D 192.168.12.2 GigabitEthernet0/0/0
Static routing table status :
[R1]
R1会根据路由表RIB把去往192.168.23.3从出接口G00/0/0 发出 传递给R2设备
R2设备会检查路由表RIB 发现到达192.168.23.3 是我直连 从而把数据包传递给R3设备
R3设备收到SIP 192.168.12.1 DIP 192.168.23.3 刚好目标IP是我自己的接口IP地址 会进行接收
R3将数据包进行返回 SIP 192.168.23.3 DIP 192.168.12.1 我们可以在R3上面写到达192.168.12.0静态路由ip route-static 192.168.12.0 255.255.255.0 GigabitEthernet0/0/1 192.168.23.2检查如下:[R3]display ip routing-table protocol static Route Flags: R - relay, D - download to fib
Public routing table : StaticDestinations : 1 Routes : 1 Configured Routes : 1
Static routing table status :
Destination/Mask Proto Pre Cost Flags NextHop Interface
192.168.12.0/24 Static 60 0 D 192.168.23.2 GigabitEthernet0/0/1
Static routing table status :
R3设备会检查路由表RIB 发现到达192.168.12.1 从而把数据包传递给R2设备
R2设备会检查路由表RIB 发现到达192.168.12.1 是我直连 从而把数据包传递给R1设备
R1设备收到SIP 192.168.23.3 DIP 192.168.12.1 刚好目标IP是我自己的接口IP地址 会进行接收
第三步:能够访问成功
--- 192.168.23.3 ping statistics ---5 packet(s) transmitted5 packet(s) received0.00% packet lossround-trip min/avg/max = 20/34/50 ms
2、静态路由应用场景小型网络 用静态路由来保证咱们数据传输大型网络 静态路由优化咱们网络架构
3、静态路由的缺点人工配置,配置量大,容易出错
如果配置错误了 用TTL值来防环
默认路由
MA网络 多路访问 比如:EthernetA、使用下一跳B、使用出接口+下一跳
P2P网络 点对点网络比如:PPPA、使用出接口B、使用下一跳C、使用出接口+下一跳
3、负载分担和浮动路由介绍
负载分担 当断掉其中一个链路 立马就可以通信
版权声明:本文内容由网络用户投稿,版权归原作者所有,本站不拥有其著作权,亦不承担相应法律责任。如果您发现本站中有涉嫌抄袭或描述失实的内容,请联系我们jiasou666@gmail.com 处理,核实后本网站将在24小时内删除侵权内容。
发表评论
暂时没有评论,来抢沙发吧~