理论+实操 ：华为NAT地址转换（理论 实操 安全教育课）
前言：nat地址转换可以让私有地址转换成公网地址，解决上网问题华为的三层交换机内不可以配ip地址，需要配vlanif
在企业当中，数据流量业务比较多时，用好一点的路由器多个私网地址对应外网口ip地址需要设置acl规则，只允许某个网段通行，后面跟子网反掩码接着到外网口宣告一下，acl的编号即可
网路地址转换
一： NAT概述
1.1 NAT的概念与实现方式
The device is running!
system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]un in en
Info: Information center is disabled.
[Huawei]sysname LSW1
[LSW1]vlan bat 10 20 30 40
Info: This operation may take a few seconds. Please wait for a moment...done.
[LSW1]int g 0/0/1
[LSW1-GigabitEthernet0/0/1]p l a
[LSW1-GigabitEthernet0/0/1]p d v 10
[LSW1-GigabitEthernet0/0/1]un sh
Info: Interface GigabitEthernet0/0/1 is not shutdown.
[LSW1-GigabitEthernet0/0/1]int g 0/0/2
[LSW1-GigabitEthernet0/0/2]p l a
[LSW1-GigabitEthernet0/0/2]p d v 20
[LSW1-GigabitEthernet0/0/2]un sh
Info: Interface GigabitEthernet0/0/2 is not shutdown.
[LSW1-GigabitEthernet0/0/2]int g 0/0/3
[LSW1-GigabitEthernet0/0/3]p l a
[LSW1-GigabitEthernet0/0/3]p d v 30
[LSW1-GigabitEthernet0/0/3]un sh
Info: Interface GigabitEthernet0/0/3 is not shutdown.
[LSW1-GigabitEthernet0/0/3]int g 0/0/4
[LSW1-GigabitEthernet0/0/4]p l a
[LSW1-GigabitEthernet0/0/4]p d v 30
[LSW1-GigabitEthernet0/0/4]un sh
Info: Interface GigabitEthernet0/0/4 is not shutdown.
[LSW1-GigabitEthernet0/0/4]int g 0/0/6
[LSW1-GigabitEthernet0/0/6]p l a
[LSW1-GigabitEthernet0/0/6]p d v 10
[LSW1-GigabitEthernet0/0/6]un sh
Info: Interface GigabitEthernet0/0/6 is not shutdown.
[LSW1-GigabitEthernet0/0/6]int g 0/0/5
[LSW1-GigabitEthernet0/0/5]p l a
[LSW1-GigabitEthernet0/0/5]p d v 40
[LSW1-GigabitEthernet0/0/5]un sh
Info: Interface GigabitEthernet0/0/5 is not shutdown.
[LSW1-GigabitEthernet0/0/5]q
[LSW1]dis vlan
--------------------------------------------------------------------------------
1 common UT:GE0/0/7(D) GE0/0/8(D) GE0/0/9(D) GE0/0/10(D)
GE0/0/11(D) GE0/0/12(D) GE0/0/13(D) GE0/0/14(D)
GE0/0/15(D) GE0/0/16(D) GE0/0/17(D) GE0/0/18(D)
GE0/0/19(D) GE0/0/20(D) GE0/0/21(D) GE0/0/22(D)
GE0/0/23(D) GE0/0/24(D)
10 common UT:GE0/0/1(U) GE0/0/6(U)
20 common UT:GE0/0/2(U)
30 common UT:GE0/0/3(U) GE0/0/4(U)
40 common UT:GE0/0/5(U)
[LSW1]int vlanif 10
[LSW1-Vlanif10]ip add 192.168.10.1 24
[LSW1-Vlanif10]dis this
#
interface Vlanif10
ip address 192.168.10.1 255.255.255.0
#
return
[LSW1-Vlanif10]un sh
Info: Interface Vlanif10 is not shutdown.
[LSW1-Vlanif10]int vlanif 20
[LSW1-Vlanif20]ip add 192.168.20.1 24
[LSW1-Vlanif20]un sh
Info: Interface Vlanif20 is not shutdown.
[LSW1-Vlanif20]int vlanif 30
[LSW1-Vlanif30]ip add 192.168.30.1 24
[LSW1-Vlanif30]un sh
Info: Interface Vlanif30 is not shutdown.
[LSW1-Vlanif30]int vlanif 40
[LSW1-Vlanif40]ip add 11.0.0.2 24
[LSW1-Vlanif40]un sh
Info: Interface Vlanif40 is not shutdown.
[LSW1-Vlanif40]q
[LSW1]dis interface b
Interface PHY Protocol InUti OutUti inErrors outErrors
GigabitEthernet0/0/1 up up 0% 0% 0 0
GigabitEthernet0/0/2 up up 0% 0% 0 0
GigabitEthernet0/0/3 up up 0% 0% 0 0
GigabitEthernet0/0/4 up up 0% 0% 0 0
GigabitEthernet0/0/5 up up 0% 0% 0 0
GigabitEthernet0/0/6 up up 0% 0% 0 0
Vlanif10 up up -- -- 0 0
Vlanif20 up up -- -- 0 0
Vlanif30 up up -- -- 0 0
Vlanif40 up up -- -- 0 0
[LSW1]dis ip routing-table
Destination/Mask Proto Pre Cost Flags NextHop Interface
11.0.0.0/24 Direct 0 0 D 11.0.0.2 Vlanif40
11.0.0.2/32 Direct 0 0 D 127.0.0.1 Vlanif40
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.10.0/24 Direct 0 0 D 192.168.10.1 Vlanif10
192.168.10.1/32 Direct 0 0 D 127.0.0.1 Vlanif10
192.168.20.0/24 Direct 0 0 D 192.168.20.1 Vlanif20
192.168.20.1/32 Direct 0 0 D 127.0.0.1 Vlanif20
192.168.30.0/24 Direct 0 0 D 192.168.30.1 Vlanif30
192.168.30.1/32 Direct 0 0 D 127.0.0.1 Vlanif30
[LSW1]ip route-static 0.0.0.0 0.0.0.0 11.0.0.1
R2配置
The device is running!
sys
Enter system view, return user view with Ctrl+Z.
[Huawei]un in en
Info: Information center is disabled.
[Huawei]sysname R2
[R2]int g 0/0/0
[R2-GigabitEthernet0/0/0]ip add 12.0.0.2 24
[R2-GigabitEthernet0/0/0]un sh
Info: Interface GigabitEthernet0/0/0 is not shutdown.
[R2-GigabitEthernet0/0/0]int g 0/0/1
[R2-GigabitEthernet0/0/1]ip add 13.0.0.1 24
[R2-GigabitEthernet0/0/1]un sh
Info: Interface GigabitEthernet0/0/1 is not shutdown.
[R2-GigabitEthernet0/0/1]q
[R2]int LoopBack 0
[R2-LoopBack0]ip add 114.114.114.114 32
[R2-LoopBack0]q
[R2]dis ip routing-table
Destination/Mask Proto Pre Cost Flags NextHop Interface
12.0.0.0/24 Direct 0 0 D 12.0.0.2 GigabitEthernet
0/0/0
12.0.0.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
12.0.0.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
13.0.0.0/24 Direct 0 0 D 13.0.0.1 GigabitEthernet
0/0/1
13.0.0.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
13.0.0.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
114.114.114.114/32 Direct 0 0 D 127.0.0.1 LoopBack0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
[R2]ip route-static 8.8.8.8 32 12.0.0.1
2.2 NAT router 配置，先配置第一种的静态nat转换，全局模式下配置，接口开启功能
The device is running!
system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]un in en
Info: Information center is disabled.
[Huawei]sysname NAT router
[NAT router]int g 0/0/0
[NAT router-GigabitEthernet0/0/0]ip add 11.0.0.1 24
[NAT router-GigabitEthernet0/0/0]un sh
Info: Interface GigabitEthernet0/0/0 is not shutdown.
[NAT router-GigabitEthernet0/0/0]int g 0/0/1
[NAT router-GigabitEthernet0/0/1]ip add 12.0.0.1 24
[NAT router-GigabitEthernet0/0/1]un sh
Info: Interface GigabitEthernet0/0/1 is not shutdown.
[NAT router-GigabitEthernet0/0/1]q
[NAT router]nat static global 8.8.8.8 inside 192.168.10.10
[NAT router]ip route-static 192.168.0.0 16 11.0.0.2
[NAT router]int g 0/0/1
[NAT router-GigabitEthernet0/0/1]nat static enable
[NAT router-GigabitEthernet0/0/1]q
[NAT router]ip route-static 114.114.114.114 32 12.0.0.2
2.3 配置静态NAT的第二种配法，在接口内配置
[NAT router]nat static global 9.9.9.9 inside 192.168.20.10
[NAT router]int g 0/0/1
[NAT router-GigabitEthernet0/0/1]nat static global 9.9.9.9 inside 192.168.20.10
Info: The NAT in the network has existed.
Already existing configuration will be covered with current configure. [Y/N]:
y
[NAT router-GigabitEthernet0/0/1]
R2配置回程路由
[R2]ip route-static 9.9.9.9 32 12.0.0.1
2.4 设置动态nat地址转换，即多对多的模式，
在全局模式下把两个网段（公网和私网）宣告，私网是acl ，公网是address-group ，然后在公网接口 处宣告两者之间的关系
[NAT router]dis ip routing-table
Destination/Mask Proto Pre Cost Flags NextHop Interface
8.8.8.8/32 Unr 64 0 D 127.0.0.1 InLoopBack0
9.9.9.9/32 Unr 64 0 D 127.0.0.1 InLoopBack0
11.0.0.0/24 Direct 0 0 D 11.0.0.1 GigabitEthernet
0/0/0
11.0.0.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
11.0.0.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
12.0.0.0/24 Direct 0 0 D 12.0.0.1 GigabitEthernet
0/0/1
12.0.0.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
12.0.0.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
114.114.114.114/32 Static 60 0 RD 12.0.0.2 GigabitEthernet
0/0/1
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.0.0/16 Static 60 0 RD 11.0.0.2 GigabitEthernet
0/0/0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
[NAT router]ip route-static 0.0.0.0 0.0.0.0 12.0.0.2
system-view
Enter system view, return user view with Ctrl+Z.
[NAT router]nat address-group 1 212.0.0.100 212.0.0.200
[NAT router]acl 2000
[NAT router-acl-basic-2000]rule permit source 192.168.30.0 0.0.0.255
[NAT router-acl-basic-2000]q
[NAT router]int g 0/0/1
[NAT router-GigabitEthernet0/0/1]nat outbound 2000 address-group 1 no-pat
[NAT router-GigabitEthernet0/0/1]
与此对应的，增加R2的回程路由
[R2]ip route-static 212.0.0.0 24 12.0.0.1
2.5 配置nat模式中多个私网地址对应一个公网地址
思路跟动态nat思路大致相同，全局模式下宣告私网地址网段，acl，要注意的是这种nat命令跟动态nat命令的不同之处在有一个ip 字符然后在公网接口处指定关系，因为没有指定的公网网段，不填因为环境中pc没有富裕的，需要把之前的部分配置删掉，以免冲突
system-view
Enter system view, return user view with Ctrl+Z.
[NAT router]acl 3000
[NAT router-acl-adv-3000]rule permit ip source 192.168.30.0 0.0.0.255
[NAT router-acl-adv-3000]q
[NAT router]int g 0/0/1
[NAT router-GigabitEthernet0/0/1]nat outbound 3000
[NAT router-GigabitEthernet0/0/1]dis this
[V200R003C00]
#
interface GigabitEthernet0/0/1
ip address 12.0.0.1 255.255.255.0
nat static global 9.9.9.9 inside 192.168.20.10 netmask 255.255.255.255
nat outbound 2000 address-group 1 no-pat
nat outbound 3000
nat static enable
#
return
[NAT router-GigabitEthernet0/0/1]undo nat outbound 2000 address-group 1 no-pat
[NAT router-GigabitEthernet0/0/1]undo nat static global 9.9.9.9 inside 192.168.2
0.10 netmask 255.255.255.255
[NAT router-GigabitEthernet0/0/1]q
[NAT router]
版权声明：本文内容由网络用户投稿，版权归原作者所有，本站不拥有其著作权，亦不承担相应法律责任。如果您发现本站中有涉嫌抄袭或描述失实的内容，请联系我们jiasou666@gmail.com 处理，核实后本网站将在24小时内删除侵权内容。
暂时没有评论，来抢沙发吧~