动态路由——OSPF高级配置 实验篇 （四）

动态路由——OSPF高级配置 实验篇 （四）

搭建OSPF高级配置实验

搭建拓扑图

在GNS 3中拓扑区域添加6台路由设别，其中一台R6路由设备作为网络运营商提供的网络设备路由，在R3路由设备中添加两块单口业务单板，分别用于连接外部网络路由与PC机；添加四台PC机与路由设备连接，其中PC3作为网络运营商的服务器设备，与R3路由设备相连。其中划分三个区域area 0、area 2、RIP；分别路由设备与PC接口处标注网段信息，如图所示：

网段划分：

192.168.10.0/24 192.168.20.0/24 192.168.30.0/24 192.168.40.0/24 192.168.50.0/24 192.168.60.0/24 192.168.70.0/24 12.0.0.0/24 13.0.0.0/24

Router ID 划分：

R2：2.2.2.2 R3：3.3.3.3 R4：4.4.4.4

搭建实验

1、首先在R1路由设备中添加网段地址，并设置将R1路由设备配置为默认路由。

R1#conf t //进入全局配置模式 Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int f0/0 //进入f0/0接口 R1(config-if)#ip add 192.168.10.1 255.255.255.0 //添加IP地址 R1(config-if)#no shut //开启接口 R1(config-if)# *Mar 1 00:01:10.451: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 00:01:11.451: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R1(config-if)#int f0/1 //进入f0/1接口 R1(config-if)#ip add 192.168.20.1 255.255.255.0 //添加IP地址 R1(config-if)#no shut //开启接口 R1(config-if)# *Mar 1 00:01:44.735: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up *Mar 1 00:01:45.735: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up R1(config-if)#exit //退出接口模式 R1(config)#ip route 0.0.0.0 0.0.0.0 192.168.20.2 //配置默认路由 R1(config)#do show ip route //查看路由表 Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is 192.168.20.2 to network 0.0.0.0 C 192.168.10.0/24 is directly connected, FastEthernet0/0 C 192.168.20.0/24 is directly connected, FastEthernet0/1 S* 0.0.0.0/0 [1/0] via 192.168.20.2 //配置成功

2、进入R2路由设备，配置接口地址，启动OSPF协议，设置宣告Router ID、网段信息；设置静态路由用于连接默认路由网段，最后在OSPF协议中注入直连网段信息与静态相连的默认路由网段信息。

R2#conf t //进入全局配置模式 Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int f0/0 //进入f0/0接口 R2(config-if)#ip add 192.168.30.1 255.255.255.0 //添加IP地址 R2(config-if)#no shut //开启接口 R2(config-if)# *Mar 1 00:11:10.515: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 00:11:11.515: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R2(config-if)#int f0/1 //进入f0/1接口 R2(config-if)#ip add 192.168.20.2 255.255.255.0 //添加IP地址 R2(config-if)#no shut //开启接口 R2(config-if)# *Mar 1 00:11:49.983: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up *Mar 1 00:11:50.983: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up R2(config-if)#exit R2(config)#router ospf 1 //开启ospf协议，进程号为1 R2(config-router)#router-id 2.2.2.2 //设置并宣告Router ID R2(config-router)#network 192.168.30.0 0.0.0.255 area 1 //在area 1区域中宣告网段信息 R2(config-router)#exit //退出ospf协议 R2(config)#ip route 192.168.10.0 255.255.255.0 192.168.20.1 //配置静态路由信息 R2(config)#router ospf 1 //进入ospf协议 R2(config-router)#redistribute connected subnets //注入直连网段信息 R2(config-router)#redistribute static subnets //注入默认路由网段信息 R2(config-router)#ex //退出协议 R2(config)#do show ip route //查看路由表信息 Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set C 192.168.30.0/24 is directly connected, FastEthernet0/0 S 192.168.10.0/24 [1/0] via 192.168.20.1 //成功添加网段信息 C 192.168.20.0/24 is directly connected, FastEthernet0/1

3、在R3路由设备中配置接口IP地址；配置默认路由连接外部网段；开启OSPF协议，设置Router ID，并在区域中宣告网段，注入设置的外部默认路由网段信息。

R3#conf t //进入全局配置模式 Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int f0/0 //进入f0/0接口 R3(config-if)#ip add 192.168.30.2 255.255.255.0 //添加IP地址 R3(config-if)#no shut //开启接口 R3(config-if)# *Mar 1 00:42:41.963: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 00:42:42.963: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R3(config-if)#int f0/1 //进入f0/1接口 R3(config-if)#ip add 192.168.40.1 255.255.255.0 //添加IP地址 R3(config-if)#no shut //开启接口 R3(config-if)# *Mar 1 00:43:23.963: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up *Mar 1 00:43:24.963: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up R3(config-if)#int f1/0 //进入f1/0接口 R3(config-if)#ip add 12.0.0.1 255.255.255.0 //添加IP地址 R3(config-if)#no shut //开启接口 R3(config-if)# *Mar 1 00:44:01.631: %LINK-3-UPDOWN: Interface FastEthernet1/0, changed state to up *Mar 1 00:44:02.631: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up R3(config-if)#int f2/0 //进入f2/0接口 R3(config-if)#ip add 192.168.70.1 255.255.255.0 //添加IP地址 R3(config-if)#no shut //开启接口 R3(config-if)# *Mar 1 00:44:41.015: %LINK-3-UPDOWN: Interface FastEthernet2/0, changed state to up *Mar 1 00:44:42.015: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2/0, changed state to up R3(config-if)#do show ip int b //查看接口信息 Interface IP-Address OK? Method Status Protocol FastEthernet0/0 192.168.30.2 YES manual up up FastEthernet0/1 192.168.40.1 YES manual up up FastEthernet1/0 12.0.0.1 YES manual up up FastEthernet2/0 192.168.70.1 YES manual up up //成功添加网段 R3(config)#ip route 0.0.0.0 0.0.0.0 12.0.0.2 //配置默认路由，连接外部网段 R3(config)#router ospf 1 //开启ospf协议，进程号为1 R3(config-router)#router-id 3.3.3.3 //设置宣告Router ID R3(config-router)#network 192.168.30.0 0.0.0.255 area 1 //在area 1区域中宣告网段信息，注意子网掩码写反码 R3(config-router)# *Mar 1 00:47:50.531: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on FastEthernet0/0 from LOADING to FULL, Loading Done R3(config-router)#network 192.168.40.0 0.0.0.255 area 0 //在area 0区域中宣告网段信息，注意子网掩码写反码 R3(config-router)#network 192.168.70.0 0.0.0.255 area 0 R3(config-router)#default-information originate //将外部路由网段注入ospf协议中 R3(config-router)#ex //退出 R3(config)#do show ip route //查看路由表 Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is 12.0.0.2 to network 0.0.0.0 C 192.168.30.0/24 is directly connected, FastEthernet0/0 O E2 192.168.10.0/24 [110/20] via 192.168.30.1, 00:01:21, FastEthernet0/0 C 192.168.40.0/24 is directly connected, FastEthernet0/1 O E2 192.168.20.0/24 [110/20] via 192.168.30.1, 00:01:21, FastEthernet0/0 12.0.0.0/24 is subnetted, 1 subnets C 12.0.0.0 is directly connected, FastEthernet1/0 C 192.168.70.0/24 is directly connected, FastEthernet2/0 S* 0.0.0.0/0 [1/0] via 12.0.0.2 //成功添加网段

4、在R4路由设备添加接口IP地址，启用RIP协议，启用版本2，关闭路由自动汇总功能，宣告网段信息，最后注入OSPF协议，设置跳数为5；启用OSPF协议，设置Router ID，并在区域中宣告网段，注入RIP协议。

R4#conf t //进入全局配置模式 Enter configuration commands, one per line. End with CNTL/Z. R4(config)#int f0/0 //进入f0/0接口 R4(config-if)#ip add 192.168.40.2 255.255.255.0 //添加IP地址 R4(config-if)#no shut //开启接口 R4(config-if)# *Mar 1 01:03:22.375: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 01:03:23.375: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R4(config-if)#int f0/1 //进入f0/1接口 R4(config-if)#ip add 192.168.50.1 255.255.255.0 //添加IP地址 R4(config-if)#no shut //开启接口 R4(config-if)# *Mar 1 01:03:57.519: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up *Mar 1 01:03:58.519: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up R4(config-if)#ex //退出接口模式 R4(config)#router rip //启用RIP协议 R4(config-router)#version 2 //启用版本2 R4(config-router)#no auto-summary //关闭路由自动汇总功能 R4(config-router)#network 192.168.50.0 //宣告网段 R4(config-router)#redistribute ospf 1 metric 5 //注入ospf协议，设置条数为5 R4(config-router)#ex //退出 R4(config)#router ospf 1 //开启ospf协议，进程号为1 R4(config-router)#router-id 4.4.4.4 //设置宣告Router ID R4(config-router)#network 192.168.40.0 0.0.0.255 area 0 //在area 0区域中宣告网段信息，注意子网掩码写反码 R4(config-router)# *Mar 1 01:10:09.027: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on FastEthernet0/0 from LOADING to FULL, Loading Done R4(config-router)#redistribute rip subnets //注入RIP协议 R4(config-router)#ex //退出 R4(config)#do show ip route //查看路由表 Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is 192.168.40.1 to network 0.0.0.0 O IA 192.168.30.0/24 [110/20] via 192.168.40.1, 00:01:30, FastEthernet0/0 O E2 192.168.10.0/24 [110/20] via 192.168.40.1, 00:01:30, FastEthernet0/0 C 192.168.40.0/24 is directly connected, FastEthernet0/0 O E2 192.168.20.0/24 [110/20] via 192.168.40.1, 00:01:30, FastEthernet0/0 C 192.168.50.0/24 is directly connected, FastEthernet0/1 O 192.168.70.0/24 [110/11] via 192.168.40.1, 00:01:30, FastEthernet0/0 O*E2 0.0.0.0/0 [110/1] via 192.168.40.1, 00:01:30, FastEthernet0/0 //成功学习网段信息

5、在R5路由设备中添加接口IP地址，启用RIP协议，并关闭自动汇总功能，宣告两个网段。

R5#conf t //进入全局配置模式 Enter configuration commands, one per line. End with CNTL/Z. R5(config)#int f0/0 //进入f0/0接口 R5(config-if)#ip add 192.168.50.2 255.255.255.0 //添加IP地址 R5(config-if)#no shut //开启接口 R5(config-if)# *Mar 1 01:27:42.539: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 01:27:43.539: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R5(config-if)#int f0/1 //进入接口f0/1 R5(config-if)#ip add 192.168.60.1 255.255.255.0 //添加IP地址 R5(config-if)#no shut //开启接口 R5(config-if)# *Mar 1 01:28:17.635: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up *Mar 1 01:28:18.635: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up R5(config-if)#router rip //启用RIP协议 R5(config-router)#version 2 //启用版本2 R5(config-router)#no auto-summary //关闭自动汇总功能 R5(config-router)#network 192.168.50.0 //宣告网段信息 R5(config-router)#network 192.168.60.0 R5(config-router)#ex //退出 R5(config)#do show ip route //查看路由表 Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is 192.168.50.1 to network 0.0.0.0 R 192.168.30.0/24 [120/5] via 192.168.50.1, 00:00:25, FastEthernet0/0 C 192.168.60.0/24 is directly connected, FastEthernet0/1 R 192.168.10.0/24 [120/5] via 192.168.50.1, 00:00:25, FastEthernet0/0 R 192.168.40.0/24 [120/5] via 192.168.50.1, 00:00:25, FastEthernet0/0 R 192.168.20.0/24 [120/5] via 192.168.50.1, 00:00:25, FastEthernet0/0 C 192.168.50.0/24 is directly connected, FastEthernet0/0 R 192.168.70.0/24 [120/5] via 192.168.50.1, 00:00:25, FastEthernet0/0 R* 0.0.0.0/0 [120/1] via 192.168.50.1, 00:00:26, FastEthernet0/0 //成功学习网段信息

6、在R6路由设备中添加接口IP地址，然后配置静态路由。

R6#conf t //进入全局配置模式 Enter configuration commands, one per line. End with CNTL/Z. R6(config)#int f0/0 //进入f0/0接口 R6(config-if)#ip add 12.0.0.2 255.255.255.0 //添加IP地址 R6(config-if)#no shut //开启接口 R6(config-if)# *Mar 1 01:36:54.323: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 01:36:55.323: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R6(config-if)#int f0/1 //进入接口f0/1 R6(config-if)#ip add 13.0.0.1 255.255.255.0 //添加IP地址 R6(config-if)#no shut //开启接口 R6(config-if)# *Mar 1 01:37:26.223: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up *Mar 1 01:37:27.223: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up R6(config-if)#ex //退出模式 R6(config)#ip route 192.168.0.0 255.255.0.0 12.0.0.1 //设置静态路由 R6(config)#do show ip route //查看路由表 Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set 12.0.0.0/24 is subnetted, 1 subnets C 12.0.0.0 is directly connected, FastEthernet0/0 13.0.0.0/24 is subnetted, 1 subnets C 13.0.0.0 is directly connected, FastEthernet0/1 S 192.168.0.0/16 [1/0] via 12.0.0.1 //网段添加成功

7、分别在PC机中添加IP地址，并测试网络互通性。

PC1> ip 192.168.10.2 192.168.10.1 //添加IP地址 Checking for duplicate address... PC1 : 192.168.10.2 255.255.255.0 gateway 192.168.10.1

PC2> ip 192.168.70.2 192.168.70.1 //添加IP地址 Checking for duplicate address... PC1 : 192.168.70.2 255.255.255.0 gateway 192.168.70.1

PC3> ip 13.0.0.2 13.0.0.1 //添加IP地址 Checking for duplicate address... PC1 : 13.0.0.2 255.255.255.0 gateway 13.0.0.1

P4> ip 192.168.60.2 192.168.60.1 //添加IP地址 Checking for duplicate address... PC1 : 192.168.60.2 255.255.255.0 gateway 192.168.60.1

PC1> ping 192.168.70.2 //测试PC1与PC2的互通性 192.168.70.2 icmp_seq=1 timeout 192.168.70.2 icmp_seq=2 timeout 84 bytes from 192.168.70.2 icmp_seq=3 ttl=61 time=53.853 ms 84 bytes from 192.168.70.2 icmp_seq=4 ttl=61 time=60.168 ms 84 bytes from 192.168.70.2 icmp_seq=5 ttl=61 time=57.781 ms //成功通信 PC1> ping 13.0.0.2 //测试PC1与PC3的互通性 13.0.0.2 icmp_seq=1 timeout 13.0.0.2 icmp_seq=2 timeout 84 bytes from 13.0.0.2 icmp_seq=3 ttl=60 time=76.872 ms 84 bytes from 13.0.0.2 icmp_seq=4 ttl=60 time=83.919 ms 84 bytes from 13.0.0.2 icmp_seq=5 ttl=60 time=77.712 ms //成功通信 PC1> ping 192.168.60.2 //测试PC1与P4的互通性 192.168.60.2 icmp_seq=1 timeout 84 bytes from 192.168.60.2 icmp_seq=2 ttl=59 time=97.596 ms 84 bytes from 192.168.60.2 icmp_seq=3 ttl=59 time=97.688 ms 84 bytes from 192.168.60.2 icmp_seq=4 ttl=59 time=99.732 ms 84 bytes from 192.168.60.2 icmp_seq=5 ttl=59 time=103.440 ms //成功通信

PC2> ping 13.0.0.2 //测试PC2与PC3的互通性 13.0.0.2 icmp_seq=1 timeout 13.0.0.2 icmp_seq=2 timeout 84 bytes from 13.0.0.2 icmp_seq=3 ttl=62 time=38.042 ms 84 bytes from 13.0.0.2 icmp_seq=4 ttl=62 time=37.842 ms 84 bytes from 13.0.0.2 icmp_seq=5 ttl=62 time=40.034 ms //成功通信 PC2> ping 192.168.60.2 //测试PC2与P4的互通性 192.168.60.2 icmp_seq=1 timeout 192.168.60.2 icmp_seq=2 timeout 84 bytes from 192.168.60.2 icmp_seq=3 ttl=61 time=56.783 ms 84 bytes from 192.168.60.2 icmp_seq=4 ttl=61 time=63.372 ms 84 bytes from 192.168.60.2 icmp_seq=5 ttl=61 time=53.795 ms //成功通信

PC3> ping 192.168.60.2 //测试PC3与P4的互通性 84 bytes from 192.168.60.2 icmp_seq=1 ttl=60 time=78.788 ms 84 bytes from 192.168.60.2 icmp_seq=2 ttl=60 time=79.786 ms 84 bytes from 192.168.60.2 icmp_seq=3 ttl=60 time=87.773 ms 84 bytes from 192.168.60.2 icmp_seq=4 ttl=60 time=84.850 ms 84 bytes from 192.168.60.2 icmp_seq=5 ttl=60 time=84.778 ms //成功通信

版权声明：本文内容由网络用户投稿，版权归原作者所有，本站不拥有其著作权，亦不承担相应法律责任。如果您发现本站中有涉嫌抄袭或描述失实的内容，请联系我们jiasou666@gmail.com 处理，核实后本网站将在24小时内删除侵权内容。