H3C堆叠irf（h3c s5130堆叠）

H3C堆叠irf（h3c s5130堆叠）

设备：

S5130-28S-SIS5130-52S-SI

同版本，不同型号

接线：

（端口均使用万兆光模块）

28S配置：

#优先级修改为32（最高，默认1）成为主设备 system-view [H3C] irf member 2 priority 32 [H3C-if-range] quit system-view [H3C] interface range ten-gigabitethernet 1/0/25 to ten-gigabitethernet 1/0/26 [H3C-if-range] shutdown [H3C-if-range] quit #绑定物理端口和irf端口 [H3C] irf-port 1/1 [H3C-irf-port1/1] port group interface ten-gigabitethernet 1/0/25 [H3C-irf-port1/1] quit [H3C] irf-port 1/2 [H3C-irf-port1/1] port group interface ten-gigabitethernet 1/0/26 [H3C-irf-port1/2] quit [H3C] interface range ten-gigabitethernet 1/0/25 to ten-gigabitethernet 1/0/26 [H3C-if-range] undo shutdown [H3C-if-range] quit [H3C] save #激活irf配置（如果没有保存以上配置就激活，配置将会失败，交换机一直重启 [H3C] irf-port-configuration active

52S配置

system-view [H3C] irf member 1 renumber 2 [H3C] irf member 2 priority 1 Renumbering the member ID may result in configuration change or loss. Continue? [Y/N]:y [H3C] quit reboot system-view [H3C] interface range ten-gigabitethernet 1/0/51 to ten-gigabitethernet 1/0/52 [H3C-if-range] shutdown [H3C-if-range] quit #绑定物理端口和irf端口 [H3C] irf-port 2/1 [H3C-irf-port2/1] port group interface ten-gigabitethernet 2/0/51 [H3C-irf-port2/1] quit [H3C] irf-port 2/2 [H3C-irf-port2/1] port group interface ten-gigabitethernet 2/0/52 [H3C-irf-port2/2] quit [H3C] interface range ten-gigabitethernet 1/0/25 to ten-gigabitethernet 1/0/26 [H3C-if-range] undo shutdown [H3C-if-range] quit [H3C] save [H3C] irf-port-configuration active #重启之后irf堆叠就建立起来了

配置BFD MAC

[H3C] vlan 3 [H3C-vlan3] port ten-gigabitethernet 1/0/24 ten-gigabitethernet 2/0/24 [H3C-vlan3] quit [H3C] interface vlan-interface 3 [H3C-Vlan-interface3] mad bfd enable [H3C-Vlan-interface3] mad ip address 192.168.2.1 24 member 1 [H3C-Vlan-interface3] mad ip address 192.168.2.2 24 member 2 [H3C-Vlan-interface3] quit #BFD和stp互斥，关闭stp [H3C] interface gigabitethernet 1/0/1 [H3C-gigabitethernet-1/0/1] undo stp enable [H3C-gigabitethernet-1/0/1] quit [H3C] interface gigabitethernet 2/0/1 [H3C-gigabitethernet-2/0/1] undo stp enable [H3C-gigabitethernet-2/0/1] quit

配置完成

主要在irf端口对应物理端口再对应到对端的物理端口和irf端口时不要搞错了，否则irf起不来还有需要万兆的光模块

版权声明：本文内容由网络用户投稿，版权归原作者所有，本站不拥有其著作权，亦不承担相应法律责任。如果您发现本站中有涉嫌抄袭或描述失实的内容，请联系我们jiasou666@gmail.com 处理，核实后本网站将在24小时内删除侵权内容。